17.5m 4 Axle Lowbed Semi Trailer for Saudi Arabia
17.5 m 4 axle lowbed semi trailer for Saudi Arabia: 80 t payload, deck height under 1.3 m, 22/14/22 mm flanges, 4 × 12T BPW axles, 17 tyres, engineering yellow
Learn More →
This 3 axle lowbed semi trailer is specified for project work in Tanzania, where the same trailer has to move a 20-tonne excavator from Dar es Salaam to an upcountry site on Monday and carry a wide roller or a set of steel plates on Tuesday. The cargo platform is 8,000 mm long and 2,600 mm wide inside a 12,050 mm overall length, and it takes a 50-tonne load on three Fuwa 13-tonne axles.
The deck is 5 mm checkered steel over a goose-neck frame with 14 mm upper and 16 mm lower flanges and an 8 mm web, framed by 25# channel side beams and 12# channel cross members. Two swing-out brackets of 300 mm each side take the usable width to 3,200 mm for wide plant, and the 300 mm side panels supplied with each unit mount on those brackets when the load needs containment.
1. A 12 m lowbed sized for Tanzanian project work
Lowbed work in Tanzania usually starts at the port or an industrial yard in Dar es Salaam and ends on a site road that may be tarmac for two hundred kilometres and gravel for the last thirty. The trailer therefore has to be light enough to run behind a standard 6×4 tractor unit, strong enough for a 50-tonne machine, and simple enough that a workshop upcountry can keep it working.
This unit measures 12,050 mm overall in length, 2,600 mm in width and 3,400 mm in height, with a 1,300 mm saddle height, so it couples to a standard tractor without a modified fifth wheel. The paint finish is red, which stays visible on site roads and at night loading.

The cargo platform is 8,000 mm long and 2,600 mm wide — long enough for a standard 20-tonne excavator with its bucket folded, or a roller plus a set of plates. The rated payload is 50 tonnes, carried on a goose-neck frame built from 14 mm upper flanges, an 8 mm web and 16 mm lower flanges, with 25# channel side beams and 12# channel cross members under a 5 mm checkered steel floor.
Checkered plate is the right floor here: it grips steel tracks and forklift tyres on a wet deck, and a worn section can be cut out and replaced without touching the frame. Six transverse beams under the gooseneck spread the load where a machine’s weight transfers as it climbs the ramps.
Wide plant is the load that most often forces a detour or a second trailer. Each side of this deck carries a swing-out bracket of 300 mm, which takes the usable width from 2,600 mm to 3,200 mm — enough for wide rollers, concrete buckets and oversized fabricated steel. The 300 mm side panels that come with each unit mount directly on the extended brackets, so a load that needs containment can be boxed in without a separate trailer.
Because the brackets swing out rather than slide, they do not intrude on the deck surface, and the trailer returns to 2,600 mm for normal highway running and for shipping.
Access is from the rear over mechanical spring-assisted ramps, which one operator can lower and raise without help. The small support legs under the ramps are removable, so the ramps can be folded flat against the deck for shipping and for loads that overhang the tail. Rope hooks and standard tighteners run along the deck edge for chains and straps, and each unit ships with wheel chocks and two fire-extinguisher holders (extinguishers supplied by the customer to local specification).

Three Fuwa 13-tonne axles run on 13 Double Coin 12R22.5 12-ply tyres on 9.0V rims — twelve on the road and one spare, mounted on the two carriers above the gooseneck. Suspension is factory-standard eight-leaf spring packs of 16 mm leaves on 8 mm-thickness suspension brackets, and the braking system uses four large and two small brake chambers on a factory-standard relay valve with ABS.

At the front, a factory-standard 50# assembly-type kingpin is bolted rather than welded, so it can be replaced as a unit, and a factory-standard landing gear set with one side tool box keeps the daily kit on the trailer. Each unit is wax coated before shipment and loaded two per set on a bulk vessel to hold the stowed volume to a minimum — the cheapest way to move 12 m trailers to Dar es Salaam. Wax coating is removed at destination before the trailer enters service. Quotations can be issued FOB a Chinese port or CIF Dar es Salaam.
The platform is 8,000 × 2,600 mm with a 50-tonne payload, so it covers excavators up to about 20 tonnes, rollers, dozers, and fabricated steel. For heavier machines the axle and tyre configuration has to be reviewed against the route.
2,600 mm standard, 3,200 mm with the swing-out 300 mm brackets on each side. The 300 mm side panels supplied with each unit mount on those brackets.
The ramps are mechanical with spring assistance; the small support legs under them are removable so the ramps can be folded flat for shipping and for over-length loads.
Yes, on a factory-standard relay valve with four large and two small brake chambers.
Yes. Platform length and width, loaded height, axle number, ramp type, side panel height and paint colour can all be set per order. Send the machine dimensions and weight, and we will return a drawing for confirmation.
Brand: Youcan
Axles: 3 Axles, Fuwa 13T each
Dimensions: 12,050mm × 2,600mm × 3,400mm
Payload: 50 tons
Cargo platform: 8,000mm × 2,600mm
Application: Excavators, rollers, dozers and wide plant for road
port and construction projects in Tanzania.
17.5 m 4 axle lowbed semi trailer for Saudi Arabia: 80 t payload, deck height under 1.3 m, 22/14/22 mm flanges, 4 × 12T BPW axles, 17 tyres, engineering yellow
Learn More →
Youcantrailer provides high quality and affordable 3 Axle lowbed/lowboy semi-trailer. Get a quote for latest price of 3 Axle lowbed, lowboy semi-trailer.
Learn More →
The Youcan lowbed trailers for all types of mechanical equipment, construction equipment can be precisely customised to match your transport business.
Learn More →