3 Axle Lowbed Semi Trailer for Tanzania
3 axle lowbed semi trailer for Tanzania: 12.05 m, 50 t payload, 8 m cargo platform, swing-out side extensions to 3.2 m width, Fuwa 13T axles, spring ramps.
Learn More →
This 17.5 m four-axle lowbed semi trailer is built for the heavy end of Saudi project logistics: excavators, wheel loaders, dozers and oversized plant that have to be moved between sites on roads that are fast in one stretch and badly patched in the next. The deck runs 17,500 mm long and 3,200 mm wide, and the loaded deck height is held at or below 1,300 mm, so tall equipment clears bridges and overhead lines without a route survey every trip.
The frame uses 22 mm upper and lower flanges with a 14 mm web, a 280 mm welded I-beam side beam and 14# channel cross members under a 5 mm checkered steel floor. Four BPW German-type 12-tonne axles on 17 Double Coin 315/80R22.5 tyres and eight 10-leaf spring packs carry the 80-tonne rating, with a JOST 50# assembly kingpin and JOST linkage landing gear at the front end.
Equipment moves in Saudi Arabia follow the project calendar: a dozer comes off one site on Thursday and has to be at the next site by Sunday, and the trailer that carries it works on highways, industrial roads and unfinished site tracks in the same trip. That sets three requirements — a deck long enough for a 20-tonne excavator plus bucket, a loaded height low enough to clear overhead structures, and a frame that does not flex when a 40-tonne machine is walked up the ramps.
This trailer answers all three. Dimensions are 17,500 mm in length and 3,200 mm in width, with an engineering-yellow paint finish that stays visible on site and in low light. The fifth-wheel interface is designed around a 50# saddle at 1,350 mm height on a single-drive 6×4 tractor unit.

The customer requirement on this build is a loaded deck height of no more than 1,300 mm, and lower where the geometry allows. That is achieved by a shallow gooseneck, a low-profile frame over a 4-axle bogie, and 315/80R22.5 tyres rather than taller 12R22.5 rubber. For the operator the practical effect is simple: excavators with a raised cab and drilling rigs with a tall mast clear most bridge and canopy limits without a permit route.Frame and deck: 22/14/22 mm flanges
The main beam runs 22 mm on the upper flange, 14 mm on the web and 22 mm on the lower flange — a heavy plate set chosen for point loads from steel-tracked machines and for the concentrated load of a forklift. The side beam is a 280 mm welded I-beam rather than a rolled channel, and the deck is carried on 14# channel cross members under a 5 mm checkered steel plate. Checkered plate gives the forklift and the machine tracks grip on a wet deck, and it is the section that wears first, so it is the section that is easiest to cut out and renew.
The deck is reinforced for forklift loading: the trailer can be loaded by forklift at the yard as well as by ramps on site, which matters when the machine is delivered to a port or a depot without a ramp.
Running gear is four BPW German-type axles of 12 tonnes, model 2300, on 17 Double Coin 315/80R22.5 tyres with 9.0V22.5 rims — sixteen on the road and one spare. Suspension is mechanical, with eight spring packs of ten leaves, 90 mm wide and 16 mm thick, which is the configuration that survives a site track without the air-bag failures that stop a lowbed in the middle of a project.

Braking uses a WABCO relay valve with six large and two small brake chambers, and manual slack adjusters so a workshop can set the brakes with a spanner. The specification is deliberately serviceable: BPW axle parts, WABCO valves and standard spring packs are all available through the parts trade that serves Saudi contractors.
Access is from the rear over spring-assisted mechanical ramps, which a single operator can fold down and lift back without a second pair of hands. Seven transverse beams under the gooseneck spread the load where the machine’s weight transfers as it climbs, and standard rope hooks and tighteners run along the deck edge for chains and straps. A factory-standard side protection net and rear protection net are fitted, and two spare wheel carriers plus one side tool box keep the daily kit on the trailer.
At the front, a JOST 50# assembly-type kingpin is bolted rather than welded, so it can be replaced as a unit, and JOST linkage landing gear raises both legs together so one person can drop the trailer. Each unit is wax coated before shipment and loaded two per set to keep the stowed volume to a minimum — the cheapest way to move 17.5 m trailers to a Saudi port. Wax coating is removed at destination before the trailer enters service. Quotations can be issued FOB a Chinese port or CIF a Saudi port.

The build is specified for a 80-tonne payload, carried over four 12-tonne BPW axles and 17 tyres. Final axle loading must be checked against the tractor unit and the local road regulation for the route.
Not higher than 1,300 mm, and lower where the frame geometry allows. This is a specified customer requirement on this build, not a catalogue figure.
Yes. The deck is 17,500 × 3,200 mm with 5 mm checkered plate over 14# channel cross members, reinforced for forklift loading as well as ramp loading.
Mechanical, with eight leaf-spring packs of ten leaves (90 mm × 16 mm). Mechanical suspension is used here because it keeps working on site tracks where air bags are vulnerable.
Yes. Deck length and width, loaded height, number of axles, ramp type, floor thickness and paint colour can all be set per order. Send the machine dimensions and weight, and we will return a drawing for confirmation.
Brand: Youcan
Model: YCH9403TDP
Axles: 4 Axles, BPW German type 2300, 12 t each
Dimensions: 17,500mm × 3,200mm
Application: Heavy equipment, excavators, dozers and oversized loose
cargo haulage for construction, quarry and infrastructure projects in Saudi Arabia.
3 axle lowbed semi trailer for Tanzania: 12.05 m, 50 t payload, 8 m cargo platform, swing-out side extensions to 3.2 m width, Fuwa 13T axles, spring ramps.
Learn More →
Youcantrailer provides high quality and affordable 3 Axle lowbed/lowboy semi-trailer. Get a quote for latest price of 3 Axle lowbed, lowboy semi-trailer.
Learn More →
The Youcan lowbed trailers for all types of mechanical equipment, construction equipment can be precisely customised to match your transport business.
Learn More →